Skip to content
Serenity Plumbing CoRaleigh, NC plumbersAnswered 24/7(919) 557-9058

Pipes, water and gas lines

Replacing gray polybutylene supply pipe in Raleigh homes

You found gray plastic pipe stamped PB2110 in the crawl space or behind the water heater, and you want to know how long it will hold.

Gray polybutylene supply pipe with crimp rings in a Raleigh crawl space

First step on arrival: trace the system

Polybutylene was installed in a great many homes from the late 1970s to the mid 1990s, the same years a lot of North Raleigh, Cary and Garner filled in with new subdivisions. It looked like a good material at the time. Over the years, the disinfectant in treated water wears on the plastic from the inside, and fittings crack without much warning. The pipe can look fine on the outside right up to the day it splits.

Serenity Plumbing replaces polybutylene with PEX or copper, running new lines to every fixture and taking out the old pipe wherever we can reach it. Most homes have running water again at the end of each work day. If you are not sure what you have, read our article on polybutylene in Raleigh homes, or call (919) 557-9058 and have one of our plumbers look at it in person.

Signs your polybutylene is near the end

Gray pipe stamped PB2110

The PB2110 code printed along the pipe confirms polybutylene, even when the line is painted or partly hidden by insulation.

Corroded crimp rings

Copper rings that look green or flaky, or gray plastic fittings with hairline cracks, are where most failures begin.

Small drips at fittings

A fitting that weeps a few drops onto the crawl space vapor barrier is often the first sign the material is giving out.

Brittle pipe near heat

Lines close to the water heater or a furnace flue age faster and may feel stiff or show a chalky white surface.

Old patch repairs

Short pieces of copper or PEX spliced into gray pipe mean the house has already had at least one failure somewhere.

Questions during a sale

Buyers' home inspectors and some insurance companies flag polybutylene, which can slow a sale or limit coverage choices.

How Serenity replaces polybutylene pipe

We start by tracing the system. In a crawl space home, that means following every gray line from the main shut-off to each fixture and noting where the pipe rises through the subfloor. In a slab home, the lines usually run through the attic and drop down inside walls. That walk-through tells us how many wall openings we need and whether existing paths can be reused for the new pipe.

Most of our polybutylene jobs use PEX, which bends around framing and can be fished through walls with small openings. We choose a manifold or a trunk and branch layout depending on the house, and we put new quarter-turn stops under every sink and toilet. Where the homeowner prefers copper, or the layout calls for it, we run copper for exposed sections near the water heater and main valve.

Polybutylene Pipe Replacement work in a Raleigh home

We work one area at a time so the house is not dry for days. At the end of each day we restore water, pressure test the new lines, and check every connection. Wall openings are kept small and square so drywall patching is simple. When we finish, the old polybutylene we can reach is cut out and hauled away, not left hanging from the joists in the crawl space.

How the job goes

01

Trace the system

We follow every gray line from the main valve to each fixture and mark where pipe passes through floors, walls and the attic.

02

Plan wall openings

You see where the small access cuts will go before we start, so furniture and keepsakes can be moved out of the way.

03

Run new lines

New PEX or copper goes in section by section, with new stops at sinks and toilets and a fresh connection at the water heater.

04

Pressure test

Each new section is tested under pressure and checked at every fitting before we close it up or move to the next area.

05

Remove old pipe

We cut out the reachable polybutylene, clean the work areas, and show you the finished runs in the crawl space or attic.

Why polybutylene keeps turning up in Triangle homes

Much of the Triangle grew quickly in the 1980s and early 1990s, and many builders used polybutylene for supply lines in that period. Subdivisions in North Raleigh, Garner and Knightdale from those years are where we find it most. A crawl space house there is often a good candidate for replacement because the main lines are easy to reach from below, which keeps wall openings to a minimum.

Earlier owners sometimes repiped only part of a house, so it is common to find gray pipe in one wing and PEX in another. We see this often in Cary and Wake Forest, where homes have changed hands several times. A slab home with attic routing needs extra care in summer, when attic heat limits working hours, so we plan those jobs around the cooler part of the day.

What polybutylene replacement costs

JobTypical range
Single bathroom or kitchen run$1,137 to $2,486
One-story home over a crawl space$4,280 to $7,615
Two-story or slab home with attic routing$6,940 to $11,370
New quarter-turn stops at all fixtures$187 to $463
Drywall patch, per opening$123 to $286

The number of fixtures, the routing path and how much wall and ceiling must be opened move the price most. A plumber gives you the real figure after walking the house. See every range in our plumbing cost guide.

Questions about polybutylene pipe replacement

Will my polybutylene fail even if it has never leaked?

Not every pipe fails on the same schedule, and some houses go decades without trouble. The problem is that failure usually comes without warning, often at a fitting, and a split line can release a lot of water before anyone notices. Most homeowners choose to replace it on their own timeline rather than waiting for a leak to pick the date for them.

Can you replace only the gray pipe that is easy to reach?

Yes, a partial job is possible, and some people start with the crawl space lines or the run feeding the water heater. The remaining polybutylene still carries the same risk, though, and a buyer's inspector will still note it. We tell you plainly what is left behind so you can plan the rest of the house when it suits you.

How many days will my water be off during a PB repipe?

On most jobs the water is off during working hours and back on each evening. A one-story crawl space home can often be finished in two to four days. Slab homes and two-story houses take longer because of the attic and wall routing. We give you a day by day plan before we start so you know what to expect.

Does my insurance company care that I still have polybutylene?

Some insurers ask about polybutylene when writing or renewing a policy, and a few limit coverage for homes that still have it. Policies differ a lot, so the best step is to ask your agent directly. After a replacement, we can give you a written description of the new piping materials and where they run to share with them.

Plumbing problem right now?

Call and a person answers, day or night. A plumber from our downtown Raleigh office comes to you.

Call (919) 557-9058
Call (919) 557-9058 · 24/7