Skip to content
Serenity Plumbing CoRaleigh, NC plumbersAnswered 24/7(919) 557-9058

Fixtures and bathrooms

Setting new toilets level and leak free in Raleigh homes

You bought a new toilet, or the old one cracked, and you want it set solid on the floor without a slow leak showing up months later.

New comfort height toilet installed in a tiled Raleigh bathroom

First step on arrival: measure rough-in

Swapping a toilet looks simple until the old bolts are rusted into a cast iron flange or the new floor sits half an inch higher than the old one. The job is mostly about what happens under the toilet: a flange at the right height, a seal that compresses evenly, and a base that does not rock. Get those right and a toilet will sit quietly for decades.

Serenity Plumbing installs standard, comfort height, dual flush, one piece and wall hung toilets. We remove and haul away the old fixture, set the new one on a fresh seal with new bolts, and replace the supply line and stop valve if they are worn. If you are planning a full bathroom remodel, we can rough in the drain for a new layout. Call (919) 557-9058 to set up a time.

Good reasons to put in a new toilet

Cracked tank or bowl

Hairline cracks in porcelain tend to grow and can let go suddenly, so a cracked toilet should be replaced, not patched.

Older high-flow model

Toilets made before the 1990s use far more water per flush than current models, which shows on every bill.

Constant repairs

When the same toilet needs parts every few months, the money is better spent on a new fixture.

Seat height is too low

A comfort height bowl, closer to chair height, is easier on knees and backs for many adults and older family members.

New floor going in

Pulling the toilet for new tile or vinyl is a natural time to replace it and raise the flange to match.

Frequent clogs

Some older low-flow toilets from the early 1990s flush poorly, and a current design clears waste much better.

How Serenity installs a toilet

Before ordering, we measure the rough-in, the distance from the finished wall to the center of the closet bolts. Most homes are 12 inches, but older houses sometimes have 10 or 14 inch rough-ins, and buying the wrong toilet means it will not fit. We also check the bathroom layout, door swing and nearby vanity so a longer elongated bowl does not crowd the room.

With the old toilet out, the flange gets a close look. It must sit on top of the finished floor, not below it, and be firmly anchored. We fix broken or low flanges with repair rings, spacers or replacement before setting the new toilet. New brass closet bolts go in, and we choose a standard wax ring or a waxless seal depending on flange height and floor type.

Toilet Installation work in a Raleigh home

The new toilet is set and pressed evenly onto the seal, shimmed where the floor is out of level, and bolted down without overtightening the porcelain. We install a new braided supply line, and if the stop valve is an old multi-turn type, we swap it for a quarter-turn. Then we flush repeatedly, check for leaks at the base, tank and supply, and adjust the fill level.

How the job goes

01

Measure rough-in

We measure from the finished wall to the closet bolts so the toilet you choose actually fits the space and layout.

02

Remove old toilet

The old toilet is drained, pulled and hauled away, and the old wax is scraped off the flange and floor.

03

Prepare the flange

We repair, raise or replace the flange as needed so it sits at the right height and is firmly anchored.

04

Set and secure

The new toilet is set on a fresh seal, shimmed level, bolted down, and connected with a new supply line.

05

Test every joint

We flush several times, check the base, tank and supply for leaks, and adjust the water level and fill valve.

Toilet installs in older and newer Triangle houses

In older Raleigh homes in Boylan Heights, Glenwood-Brooklyn and Oakwood, it is common to find a 10 inch rough-in, a cast iron flange set in an old mortar bed, or a hex tile floor that cracks easily. We take extra care pulling the old toilet so the surrounding tile is not damaged. Older bathrooms are also often small, so a compact elongated or round bowl may suit the room best.

Newer homes in Wakefield, Brier Creek and Holly Springs nearly always have 12 inch rough-ins and plastic flanges, which makes installs straightforward. The usual challenge there is a homeowner who added thicker flooring, leaving the flange recessed. Upstairs bathrooms in two-story homes deserve a solid seal, since a slow leak can stain the ceiling below before anyone notices, so we test those with extra flushes.

What toilet installation costs

JobTypical range
Install customer supplied toilet$237 to $418
Supply and install standard toilet$487 to $886
Supply and install comfort height or dual flush$612 to $1,137
Flange repair or replacement during install$163 to $447
Wall hung toilet with in-wall carrier$1,968 to $3,742

The toilet model, flange condition, rough-in size and any flooring or wall work affect the price. A plumber confirms the figure after seeing the bathroom. See every range in our plumbing cost guide.

Questions about toilet installation

How do I measure the rough-in before buying a toilet?

With the old toilet still in place, measure from the finished wall behind it, not the baseboard, to the center of one of the bolts that hold it to the floor. Most homes measure about 12 inches. If you get closer to 10 or 14, look for a toilet made for that size. If you are unsure, we can measure for you before you shop.

Is a comfort height toilet worth it for my family?

Comfort height toilets have a seat about two inches higher than standard, closer to chair height. Many adults, taller people and anyone with knee or back trouble find them easier to use. Small children may find them less comfortable, so some families put a standard height toilet in the kids' bathroom and comfort height in the main one.

Do you haul away the old toilet when you finish?

Yes. We drain the old toilet, pull it, and take it with us when we leave, along with the old wax ring and packaging from the new toilet. You do not need to arrange a bulk trash pickup. If you want to keep the old one for any reason, just tell us before we start and we will leave it where you ask.

What is the difference between wax and waxless toilet seals?

A wax ring is the traditional seal, inexpensive and reliable when the flange is at the right height and the toilet is set once. A waxless seal uses foam or rubber, can be repositioned, and handles slightly recessed flanges better. Both work well. We choose based on your flange height and floor, and the goal either way is a seal that never moves.

Plumbing problem right now?

Call and a person answers, day or night. A plumber from our downtown Raleigh office comes to you.

Call (919) 557-9058
Call (919) 557-9058 · 24/7