Fixtures and bathrooms
Kitchen, bathroom and utility sinks put in right in Raleigh
The sink is pulling away from the counter, the drain leaks into the cabinet, or you have a new vanity and nobody to hook it up.

First step on arrival: look under the sink
A sink is more than the bowl. Under it there is a drain tailpiece, a P-trap, a trap arm running into the wall, supply lines and stop valves, and often a garbage disposal or dishwasher connection. Most sink leaks come from one of those connections working loose, a trap washer drying out, or a basket strainer losing its seal against the bowl.
Serenity Plumbing repairs leaking sink drains and mounts, and installs new kitchen, bathroom, laundry and bar sinks. We handle the plumbing side of countertop and vanity projects, working with your countertop installer on timing so the sink is set and connected right after the top goes in. If the drain is slow, our drain cleaning service clears it before we hook everything up. Phone (919) 557-9058 for a visit.
Sink problems that need attention
Leak under the cabinet
A wet cabinet floor often comes from a loose trap nut, a dry washer, or a failed basket strainer seal.
Sink pulling away
An undermount sink sagging from the counter has failed clips or adhesive and can drop without warning if loaded.
Gurgling or slow drain
Gurgling as the sink drains can mean a partial clog in the trap arm or a vent that is not working properly.
Cracked or chipped bowl
Cracks in porcelain or cultured marble let water into the cabinet and get worse every time hot water runs.
Sewer smell from drain
An odor from a rarely used sink can mean the trap dried out, or an old S-trap is siphoning its water seal.
Remodel or new counters
New countertops or a new vanity mean the sink must be removed, reset and reconnected to the drain and supply.
How Serenity repairs and installs sinks
For a leaking sink, we dry the cabinet, run water and watch each joint to find the source. Basket strainers get resealed with fresh putty, trap washers and slip nuts get replaced, and old chrome or corroded metal traps get swapped for new PVC or brass. If the trap arm is not pitched toward the wall at the correct slope, we correct it so water drains fully instead of sitting in the line.
For a new sink, the type sets the approach. Drop-in sinks rest on the counter with a bead of sealant under the rim. Undermount sinks hang below the counter on clips and adhesive, and we set them before or with the countertop crew depending on the material. Vessel and pedestal sinks need their own drain heights and supply positions. We check the drain height in the wall before choosing a trap layout.

Once the sink is mounted, we connect the drain with a new trap, attach the dishwasher drain or disposal if there is one, and run new supply lines from quarter-turn stops. Older homes sometimes have S-traps, which can siphon dry; we replace those with a proper P-trap and arrange venting when needed. Then we fill the sink, let it drain, and check every joint while water is running.
How the job goes
Look under the sink
We check the drain height, trap, supply lines, stop valves and cabinet space before repairing or setting anything new.
Remove or repair
Leaking parts are resealed or replaced, or the old sink is disconnected and removed for the new installation.
Mount the sink
The new sink is set as a drop-in, undermount, vessel or pedestal, sealed to the counter and supported properly.
Connect drain and supply
A new trap, strainer and tailpiece go in, with new supply lines, and any disposal or dishwasher is connected.
Fill and check
We fill the bowl, let it drain several times, and check every connection under the cabinet while water runs.
Sink plumbing in Raleigh area kitchens and baths
Older homes in Raleigh neighborhoods like Stonehenge and North Hills often still have the original chrome traps, cast iron or galvanized drain stubs in the wall, and wall mounted lavatory sinks. Galvanized drain stubs can be nearly closed inside with buildup, so a sink that drains slowly may need the stub replaced, not just the trap. Kitchens from the 1970s and 1980s often have shallow cabinets that limit new deep sinks.
In newer homes across Apex, Cary and Wake Forest, the common jobs are swapping a drop-in for an undermount during a quartz countertop upgrade, or adding a bar sink in a basement or bonus room. Basement sinks below the main sewer line may need a small pump to lift the water. In homes on septic, we keep disposal use and drain connections in mind when planning a kitchen sink.
What sink repair and installation costs
| Job | Typical range |
|---|---|
| Reseal basket strainer or replace trap | $137 to $274 |
| Re-secure a sagging undermount sink | $212 to $438 |
| Install customer supplied bathroom sink | $243 to $487 |
| Install kitchen sink with new drain kit | $387 to $763 |
| Replace galvanized drain stub in wall | $346 to $817 |
Sink type, countertop material, the drain condition in the wall, and any disposal or dishwasher connections affect the price. A plumber confirms the figure on site. See every range in our plumbing cost guide.
Questions about sink repair & installation
Why does the cabinet under my kitchen sink keep getting wet?
The most common causes are a loose slip nut on the trap, a basket strainer that has lost its seal, a dishwasher drain hose connection that has worked loose, or a leaking faucet supply line. Dry everything with a towel, run the water, and feel each joint. If you cannot find the source, we track it down and fix every loose connection.
Can you install an undermount sink in my existing counter?
It depends on the counter. Undermount sinks need a countertop with a finished, polished cutout edge, which is normal for granite, quartz and solid surface but not for laminate. If your current counter was cut for a drop-in sink, the opening shape and edge usually will not suit an undermount. A new countertop is the usual time to switch.
What is an S-trap, and does mine need replacing?
An S-trap curves down into the floor instead of running back into the wall. Without a nearby vent, the rushing water can siphon the trap dry, which lets sewer gas into the room. They were common in older homes and are not allowed for new work under current code. If your sink smells after draining, an S-trap is worth checking.
Should I time sink work with my countertop installer?
Yes. For undermount sinks, many countertop fabricators mount the sink to the top in their shop or on site, and then a plumber connects the drain and faucet afterward. For drop-in sinks, we set the sink after the counter is installed. Let us know your countertop date and we will plan the plumbing around it.
Related
Related plumbing services
Faucet Repair & Installation
The kitchen faucet drips all night, the handle is stiff, or the new faucet you bought has been sitting in its box for...
Learn moreGarbage Disposal Repair & Installation
Your disposal hums but will not spin, trips its reset button, or leaves a puddle in the sink cabinet, and the kitchen...
Learn moreDrain Cleaning
The kitchen sink holds water after the dishes, the shower drains around your ankles, or one bathroom keeps clogging no...
Learn moreAppliance Hookups
You have a new dishwasher, refrigerator or washer sitting in the driveway, and the connections behind it need to be...
Learn morePlumbing problem right now?
Call and a person answers, day or night. A plumber from our downtown Raleigh office comes to you.