Skip to content
Serenity Plumbing CoRaleigh, NC plumbersAnswered 24/7(919) 557-9058

Fixtures and bathrooms

Kitchen and bath faucet repair and installation in Raleigh

The kitchen faucet drips all night, the handle is stiff, or the new faucet you bought has been sitting in its box for weeks.

New pull-down kitchen faucet installed over a stainless sink

First step on arrival: identify the faucet

A dripping faucet usually means one worn part: a cartridge, a ceramic disc, an O-ring or a seat washer. Fixing it the right way starts with identifying the brand and model, since most faucet parts are specific to one design. Sometimes the faucet is so old or corroded that parts are no longer sold, and installing a new one is the practical answer.

Serenity Plumbing repairs and installs kitchen, bathroom, bar and laundry faucets, including pull-down sprayers, wall mount spouts and widespread lavatory sets. Every install gets new supply lines, and we replace old multi-turn stop valves while we are under the sink. If the sink itself needs work, see our sink repair and installation page. Give us a call at (919) 557-9058 to schedule a visit.

Faucet problems that call for a repair

Drip from the spout

A steady drip after the handle is closed usually means a worn cartridge, ceramic disc or seat washer inside.

Leak at the handle base

Water around the handle or under the spout when running points to worn O-rings or a failed cartridge seal.

Stiff or loose handle

Scale buildup can make a handle hard to turn, while a loose handle often has a stripped set screw or worn adapter.

Low flow at one faucet

If only one faucet runs weak, a clogged aerator or a partly blocked cartridge is the most likely cause.

Water in the cabinet

A damp cabinet floor can come from a loose supply line, a leaking pull-down hose or a failed faucet base gasket.

Hot and cold mixed up

Temperature that drifts or reversed hot and cold sides often means a cartridge was installed wrong or has worn out.

How Serenity repairs and installs faucets

For a repair, we shut off the stops under the sink, remove the handle and trim, and pull the cartridge or stem. We match the part by brand and model, and we carry common cartridges on the truck. While the faucet is open, we clean scale from the valve body, replace the O-rings, and lubricate them with plumber's grease so the handle moves smoothly. Then we reassemble and test both hot and cold sides.

For a new install, we check the sink first: how many holes it has, their spacing, and whether the deck can support the new faucet. A single handle faucet on a three-hole sink needs a deck plate. A pull-down kitchen faucet needs clearance behind the sink and room under the cabinet for the hose and counterweight. We remove the old faucet, clean the deck, and set the new one with its gasket or a bead of putty.

Faucet Repair & Installation work in a Raleigh home

Every new faucet gets new braided supply lines. If the stop valves under the sink are old multi-turn types that barely close, we replace them with quarter-turn valves. Then we flush the lines before connecting, which keeps debris out of the new cartridge, check every connection for drips, and run the faucet hot and cold. We also check the drain connection, since moving a sink often loosens the trap.

How the job goes

01

Identify the faucet

We find the brand, model and cartridge type so the repair parts or new faucet match the sink and valve body.

02

Shut off and open

Stops under the sink are closed, the handle and trim come off, and we inspect the cartridge or stem inside.

03

Repair or remove

Worn parts are replaced, or the old faucet is removed and the deck cleaned and prepared for the new one.

04

Install and connect

The new faucet is mounted, new supply lines go on, and old stop valves are swapped for quarter-turn valves.

05

Flush and test

We flush the lines, run hot and cold, and check every connection under the sink for leaks before leaving.

Faucets and water quality around the Triangle

Most Triangle cities, including Raleigh, Cary and Chapel Hill, have relatively soft treated water, so heavy scale is less common than in many parts of the country. Even so, aerators collect sediment and grit, especially after the utility flushes hydrants or does work on a main. A faucet that slows down after street work often just needs its aerator cleaned.

Homes on private wells in rural Johnston, Franklin and Harnett counties are a different story. Well water can carry iron and minerals that stain fixtures and wear out cartridges faster. If you see orange stains or crusty aerators, a whole-house filter may protect new faucets. Older homes in Raleigh may also have galvanized supply pipe that sheds rust flakes into faucet cartridges.

What faucet repair and installation costs

JobTypical range
Cartridge or stem repair$147 to $286
Install customer supplied faucet$187 to $364
Supply and install kitchen faucet$438 to $917
Supply and install bathroom faucet$326 to $742
Replace two stop valves and supply lines$163 to $317

The faucet brand, part availability, sink type and stop valve condition affect the price. A plumber gives you the real figure after seeing the sink. See every range in our plumbing cost guide.

Questions about faucet repair & installation

Is it worth fixing a faucet or should I just replace it?

If the faucet is a known brand with parts still available and the finish is in good shape, a cartridge repair is usually the better value. If the body is corroded, the finish is worn through, or the model is decades old and parts are hard to find, a new faucet often costs only a little more and lasts much longer.

Can I buy my own faucet and have you install it?

Yes, many customers do. Before you buy, count the holes in your sink or counter and measure their spacing, and check that the faucet fits the space behind the sink. If you send us the model, we can confirm it will work. We install it with new supply lines, and we will let you know if any parts are missing from the box.

Why does my new faucet sputter and spit air?

Air in the lines after a faucet install or after water was shut off is normal for a few moments. If it keeps sputtering, debris may be caught in the aerator or cartridge, or the supply lines may have been connected without flushing first. Remove and clean the aerator. If that does not fix it, the cartridge may need flushing.

What do the little valves under my sink actually do?

Those are fixture stop valves. They let you shut off water to one sink without turning off the whole house, which matters for faucet repairs and leaks. Older ones are multi-turn and often stick or drip when turned. Quarter-turn stops close with a simple turn of the handle and are much more reliable when you need them most.

Plumbing problem right now?

Call and a person answers, day or night. A plumber from our downtown Raleigh office comes to you.

Call (919) 557-9058
Call (919) 557-9058 · 24/7