Skip to content
Serenity Plumbing CoRaleigh, NC plumbersAnswered 24/7(919) 557-9058

Fixtures and bathrooms

Garbage disposal repair and replacement for Raleigh kitchens

Your disposal hums but will not spin, trips its reset button, or leaves a puddle in the sink cabinet, and the kitchen sink is backing up while you wait.

New garbage disposal installed under a kitchen sink in Raleigh

First step on arrival: shut off power

A garbage disposal fails in a handful of predictable ways. The flywheel jams on a fruit pit or a bottle cap, the motor overheats and trips its thermal reset, the seal at the bottom gives out and drips, or the unit simply wears through after years of use. Most are quick to sort out, and a few tell you it is time for a new unit.

Serenity Plumbing sends its own plumbers to kitchens across Raleigh and the Triangle, day or night. We carry common disposal sizes on the truck, so a dead unit can usually be replaced on the same visit. When the disposal itself is fine but water still sits in the sink, we clear the drain line past it too, because a packed trap or branch line is often what makes a healthy disposal look broken.

Signs your disposal needs a plumber

Humming with no spin

The motor is getting power but the flywheel is stuck, usually from a hard object wedged between the impeller and the grind ring.

Reset button keeps tripping

A unit that shuts itself off every few days is overheating, often from a partial jam or a motor near the end of its life.

Water under the sink

Drips from the bottom of the housing usually mean the internal seal has failed, which is not something a repair kit can fix.

Leak at the flange

Water around the top of the disposal points to loose mounting bolts or dried plumber's putty where the unit meets the sink.

Both bowls draining slowly

If both sides of a double sink drain slowly, the clog is likely in the shared trap or the wall line, not the disposal.

Grinding noise or odor

Metal on metal sounds mean something is loose inside, and a steady sour odor usually means food is packing into the drain past the unit.

How we handle a disposal call

We start by cutting power and checking the unit from below. A jam can usually be freed with the hex key socket on the bottom of the motor, and we pull out whatever was caught before testing again. If the motor spins freely but trips the reset, we check the outlet or switch circuit and the amperage draw. If the housing is wet, we trace the water to its exact source.

When a repair makes sense, we do it on the spot: a new mounting gasket, fresh flange putty, a new discharge tube gasket, or a cleared trap. When the unit itself has failed, we talk through replacement sizes plainly. A 1/3 horsepower unit suits a light user, a 1/2 or 3/4 horsepower unit handles most family kitchens, and a full horsepower model makes sense for heavy daily cooking.

Garbage Disposal Repair & Installation work in a Raleigh home

Installation includes the new mounting ring, a properly sloped discharge to the trap, and the dishwasher knockout punched out if a dishwasher drains through the disposal. A missed knockout sends dishwasher water back into the sink. Before we leave, we run water and the unit together, check every joint with a dry towel, and show you where the reset button and hex socket are.

How the job goes

01

Shut off power

We switch off the circuit or unplug the unit before anyone puts a hand or a tool near the grinding chamber, every single time.

02

Free and inspect

We clear any jam from below with the hex socket, remove the object, and check the impeller plates, grind ring and seal for wear.

03

Find the leak

Dry paper towels at each joint show whether water is coming from the flange, the dishwasher inlet, the discharge tube or the housing.

04

Repair or replace

We fix worn gaskets and loose mounts on the spot, or swap in a correctly sized new unit from the truck when the motor or seal is done.

05

Test under load

We run the disposal with water and food scraps, run the dishwasher drain if it is connected, and confirm every joint stays dry before leaving.

Disposals in Raleigh and Triangle kitchens

Many kitchens in Raleigh's newer subdivisions, from Brier Creek to Wakefield, were built with a disposal and dishwasher sharing one drain, and the original builder-grade units are often reaching the end of their life. In older homes around Five Points and Oakwood, the drain lines behind the sink may be galvanized steel or older cast iron, and those narrow over time with buildup.

The City of Raleigh asks residents to keep fats, oils and grease out of drains because grease builds up in sewer mains and causes overflows. A disposal does not change that: grease goes in the trash. In rural parts of Johnston, Franklin and Harnett counties, homes on septic systems can run a disposal, but food solids add to the tank, so pumping may be needed more often.

What disposal work typically costs

JobTypical range
Jam clearing and reset$97 to $168
Leak repair at flange or gasket$137 to $246
1/2 hp disposal, supplied and installed$318 to $487
3/4 hp disposal, supplied and installed$423 to $639
Disposal swap plus trap and drain clearing$267 to $446

The horsepower and brand you choose, whether a new outlet or switch is needed, and the condition of the drain past the unit move the price most. You get the actual figure after a plumber sees the job. See every range in our plumbing cost guide.

Questions about garbage disposal repair & installation

Can I fix a jammed disposal myself with the hex key?

Often, yes. With the power off, insert a 1/4 inch hex key into the socket on the bottom center of the unit and work it back and forth until it turns freely, then press the red reset button. If it jams again right away, or hums without spinning after a reset, something is lodged deeper or the motor is failing, and that is the point to call.

Is a leaking disposal worth repairing?

It depends on where the water is coming from. Leaks at the sink flange, the dishwasher inlet or the discharge tube are usually inexpensive gasket or putty fixes. A leak from the bottom of the housing, or rust streaks on the body, means the internal seal has failed. That cannot be rebuilt on most residential models, so replacement is the sensible choice.

What should never go down a garbage disposal?

Grease and oil, coffee grounds, eggshells, fibrous peels, pasta and rice, bones, fruit pits and anything that is not food. Run cold water before, during and for a few seconds after grinding. Cold water keeps any fats solid enough to be chopped and carried away instead of coating the pipe.

Can you replace my disposal tonight?

In most cases, yes. We answer 24/7, and our plumbers carry standard 1/2 and 3/4 horsepower units, mounting hardware and trap parts. If your sink has an unusual flange, or you want a specific premium model we do not stock, we may install it on a second visit. Give us a call at (919) 557-9058 and describe what the unit is doing.

Plumbing problem right now?

Call and a person answers, day or night. A plumber from our downtown Raleigh office comes to you.

Call (919) 557-9058
Call (919) 557-9058 · 24/7